How to Make an Apple Bong

Looking for a unique and fun way to smoke your favorite herb? Check out our tutorial on how to make an apple bong! This simple and easy-to-follow guide will have you taking big hits in no time.

Checkout this video:

Supplies

You will need the following supplies to make your apple bong: an apple, a sharp knife, a pen, a pen cap, and a bowl. You will also need a lighter and some weed.

Apples

You will need an apple, a knife, a pen, and a bowl. Any type of apple will work, but we recommend Granny Smith apples because they are firm and provide good resistance when being carved.

Cut the apple in half using the knife. Once the apple is cut in half, use the pen to poke a hole in the center of theapple. The hole should be big enough to fit the bowl snugly.

Next, take the knife and make two cuts on either side of the hole you just made. Be sure not to cut too deeply—you don’t want to cut through the other side of the apple. These cuts will create flaps that can be opened up to create a mouthpiece.

Now it’s time to open up the flaps you just created. Do this by inserting the blade of the knife into each flap and then twisting your wrist so that the blade points downwards. Once the flaps are open, you can remove them completely or leave them attached to the apple—it’s up to you.

If you want, you can use the knife to carve out a design onthe outside ofthe apple bong. When you’re finished carving, it’s time to put your new bong to use!

Knife

The first step is find a knife that you feel comfortable using. It doesn’t have to be anything fancy, just something that can get the job done. Once you have your knife, it’s time to get started.

Bowl piece

The bowl piece is the part of the bong or pipe where you load your tobacco or cannabis. It’s also called the slide. A bowl is either removable or fixed, and made of glass, metal, wood, or ceramic.

There are different types of bongs and pipes, so there are different types of bowl pieces to go with them. Some have a small hole in the side called a carburetor, which allows you to clear the chamber of smoke by momentarily covering the hole with your finger while taking a hit.

Downstem

The downstem is a narrow tube that runs from the joint of the bong to the bottom of the chamber. It functions as a route for the smoke to travel from the bowl to the water in the chamber. Many downstems are removable for easy cleaning. If your bong does not have a removable downstem, you can clean it by soaking it in isopropyl alcohol and salt.

Rubber band

You will need a rubber band for this project

Aluminum foil

Aluminum foil is a common household item that can be used for a variety of purposes. In this case, it will be used to create a bowl for your apple bong.start by shaping the foil into a small bowl. Make sure that the bowl is big enough to hold your cannabis, but not so big that it falls through the apple. Once you have the perfect size and shape, use a fork to poke small holes into the bottom of the bowl. This will allow the smoke to travel through the foil and into the apple.

Steps

This is a guide on how to make an apple bong. An apple bong is a type of bong that is made out of an apple. It is a simple and easy way to make a bong, and only requires a few materials.

Cut the apple in half

Cut the apple in half using a sharp knife. Scoop out the inside of the apple halves using a spoon, being careful not to break through the skin. The apple should now resemble two small bowls.

Scoop out the core of the apple with a spoon, making a bowl

Be sure to leave enough apple flesh so the bowl is sturdy. Eat the apple slices or save them for later. If you want, you can use a knife to smooth out the bowl of the apple.

Take the bowl piece and fit it snugly into the core of the apple

-Remove the stem from the apple and poke a hole through the top of the apple using the tip of your knife.
-Twist the knife to widen the hole. Remove the knife and insert the bowl piece into the hole.
-Pack your herb into the bowl piece.
-Place your mouth over the carb and light your herb. Inhale slowly and steadily until the apple is filled with smoke.
-Remove the bowl piece and take a big hit!

Wrap the rubber band around the apple where the bowl piece meets the apple

1. Cut the apple in half using a sharp knife. Be extra careful not to cut yourself.
2. Scoop out the middle of the apple using a spoon, being careful not to puncture the skin.
3. Wrap the rubber band around the apple where the bowl piece meets the apple. This will keep the bowl piece from sliding off when you take a hit.
4. Cut a small hole in the bottom of the bowl piece using a knife or razor blade.
5. Put your weed in the bowl and light it up!
6. Take a big hit and enjoy!

Make a small hole in the aluminum foil and fit it over the bowl piece

Use a pen or some other sharp object to make a small hole in the center of the aluminum foil. Make sure that the hole is big enough to fit snugly over the bowl piece. If it’s too small, the foil will rip when you try to put it on, and if it’s too big, smoke will escape and you won’t get as high.

Pack the bowl with your favorite smoking material

To make an apple bong, start by carving a bowl into the side of an apple using a carving knife. Then, use a pen to poke a hole through the top of the apple and down into the bowl. Next, carve out a small hole in the bottom of the apple so smoke can escape. Once you’ve done that, put your chosen smoking material in the bowl and light it. Finally, take long, slow draws on the mouthpiece to fill the apple with smoke. When you’re ready to exhale, remove the bowl and tip the apple upside down so the smoke comes out!

Light the bowl and inhale the smoke through the apple

1. Poke a small hole in the side of the apple with a knife. Make the hole big enough to fit the bowl of your pipe.

2. Insert the bowl of your pipe into the hole.

3. Light the bowl and inhale the smoke through the apple.

4. Enjoy your apple bong!