Contents
- Open the Remote app on your iPhone, iPad, ipod touch
- If you don’t see your Apple TV, make sure that your iOS device is on the same Wi-Fi network as your Apple TV.
- If you still don’t see your Apple TV, it might be turned off. To turn it on, press and hold the Play/Pause button on the top of your Apple TV remote for 5 seconds.
- Connect your iOS device to the same Wi-Fi network as your Apple TV.
- On your iOS device, open the Remote app.
- Tap your Apple TV.
- If you’re asked for a passcode, enter the 4-digit code that appears on your Apple TV.
- If you don’t see a 4-digit code, try these steps.
- After you enter the passcode, your iOS device will pair with your Apple TV.
Learn how to charge apple tv remote by following these simple steps.
Checkout this video:
Open the Remote app on your iPhone, iPad, ipod touch
If you see a message that says your remote is low on battery, charge it for about 2 hours before you use it again.
Open the Remote app on your iOS device, then select apple tv If you don’t see apple tv make sure that your iOS device is connected to the same Wi-Fi network as your Apple TV. If you still don’t see your Apple TV, try these steps.
Select Settings > General > Remotes, then select Learn Remote. Follow the onscreen instructions to finish charging your remote.
If you don’t see your Apple TV, make sure that your iOS device is on the same Wi-Fi network as your Apple TV.
If you don’t see your Apple TV, make sure that your iOS device is on the same Wi-Fi network as your Apple TV. If you’re using an Ethernet connection, check that your Ethernet cable is plugged into the router that you use for Wi-Fi.
1. Connect your Lightning to USB Cable apple tv remote to your computer.
2. Plug in your Apple TV Remote. If it’s connected, you’ll see the green LED on your remote turn on.
3. Wait for about 5 minutes, then disconnect and reconnect your remote from USB.
If you see apple tv home screen your remote is charged and ready to use.
If you don’t see the Apple TV Home screen, check the top of your remote. If it has a green indicator light, your remote is charged and ready to use. If you don’t see a green indicator light, put your remote on the charging surface of your Apple TV for at least 10 minutes or until you see the green indicator light.
Connect your iOS device to the same Wi-Fi network as your Apple TV.
Open the Control Center on your iOS device, then tap .
Tap the device that you want to use to control your Apple TV. If you don’t see your device listed, make sure that Bluetooth is turned on.
Your Apple TV remote should appear in the Control Center.
On your iOS device, open the Remote app.
On your iOS device, open the Remote app.
To charge your Apple TV remote, connect it to your Apple TV with the Lightning to USB Cable (included with your Apple TV).
Your Apple TV remote should charge in less than an hour and last about 3 months before needing to be charged again.
Tap your Apple TV.
Tap your Apple TV.
-Open settings app
-Swipe down to and select Remotes and Devices.
-Swipe down to and select Remote ; if you don’t see Remote, swipe all the way down to the bottom and select General, then scroll all the way down and select Remotes.
-If prompts appear on your Apple TV asking you to enter a code or pair a remote, follow the onscreen instructions.
If you’re asked for a passcode, enter the 4-digit code that appears on your Apple TV.
Learn how to charge your Apple TV remote. If you’re asked for a passcode, enter the 4-digit code that appears on your Apple TV.
If you don’t see a 4-digit code, try these steps.
If you don’t see a 4-digit code, try these steps.
1. Check that your remote is using a CR2032 coin battery. If you see a green light, your remote is using an older alkaline battery. These batteries can no longer be charged and must be replaced.
2. Remove the back cover of your remote and make sure the striated, metal contact pads on the battery are touching the contact pads inside the remote. If they’re not touching, gently bend the metal contacts down so they touch the pads.
3. If you tried these steps and you still don’t see a 4-digit code, charge your remote for at least 30 minutes with a Lightning to USB cable connected to a power adapter or computer, then try again.
After you enter the passcode, your iOS device will pair with your Apple TV.
After you enter the passcode, your iOS device will pair with your Apple TV. To keep your remote charged, plug it into the Lightning connector on your iOS device. If you’re using an iPhone or iPod touch with a case, make sure that the case doesn’t block the Lightning connector. You can use your remote while it’s charging, and you don’t need to wake your iOS device when you want to use your remote control.
